B718H16206002 Removal 1 Remove the following parts from the left handlebar. This manual very useful in the treatment and repair. If the battery voltage is still less than 12. Brake hose union bolt 5. Replace the disc if the runout exceeds the service limit.
I718H1140035-01 8 Remove the intake 7 and exhaust camshafts 8. Clamp :After positioning the clamp with the stopper, tighten the clamp bolt. B718H15206017 4 Turn the gearshift link rod 2 until the gearshift lever Removal is 45 — 55 mm 1. Rear shock absorber mounting nut Upper 5. Assemble the master cylinder in the reverse order of disassembly. I718H1450068-01 Is the sensor mounted securely? I718H1110172-01 ° Throttle position approx.
Do not use or mix different types of fluid such as silicone-based or petroleum-based. Tires — Steering — — Front forks —. I718H1110198-01 Secondary throttle position approx. I718H1240040-03 6 Remove the spacer. If any defects are found, the hose with a new one. I718H1150057-01 Installation Installation is in reverse order of removal. Special tool A : 09913—70210 Bearing installer set I718H1520009-01 Countershaft Assembly 1 Remove the bearing retainer 1.
Hold the front fork by the hand to prevent 4 Remove the front fender by removing the bolts 3 , sliding out of the steering stem. If the Inspection resistance is not within the specified value, replace B718H11906008 Check the interlock system for proper operation. I718H1140044-02 4 Remove the cylinder gasket 4 and dowel pins. I718H1110247-01 4 Click each button 2. Special tool A : 09930—44530 Rotor holder 9 Loosen the generator rotor bolt.
All Manuals Are Windows and Mac compatible! Assemble the caliper in the reverse order of 4 Remove the slide pin 6. Special tool A : 09915—40610 Oil filter wrench I718H1140169-01 Crankcase Breather Cover I718H1140172-01 Remove the crankcase breather cover 1 and oil breather separator 2. Clogged oil cooler Clean or replace. Oil adhesion on friction surface of pads. Use this section as well as other sections to use as a guide for proper inspection and service. Adjust the headlight beam, both horizontally and vertically. Cushion rod mounting nut b : 78 N·m 7.
Removal 1 Support the motorcycle with the center stand. Inner tube slide metal 21. B718H11406034 Removal 1 Remove the fuel tank. Refer to 2 Remove the seat. I718H1140041-01 Cylinder 1 Disconnect the water hoses 1. Tightening torque Front brake pad mounting pin a : 16 N·m 1.
Cushion Lever Bearing Removal and Spacer Installation 1 Remove the spacers from the cushion lever. Use a new O-ring 3 to prevent oil leakage. I718H1110251-01 2 Check the secondary throttle actuator position sensor data. For the installing and removing procedures, refer to respective paragraphs describing each component. If any Install the air valve in the reverse order of removal.
Poor contact of generator lead wire Repair. Then, tighten the oil filter two full turns or to 2 Turn the adjuster 3 in or out until the throttle cable specified torque using the special tool. Faulty motor 2 Remove the left frame cover. B718H11406038 Check that the throttle grip moves smoothly from full Pay attention to the following points: open to full close. The cam chain tension adjuster is maintained at the 4 Remove the cam chain No.
Refer 8 Disconnect the headlight and position light couplers. I718H1170032-02 I718H1170036-03 6 Remove the fuel pressure regulator assembly 8. B718H14504024 1 Remove the right frame cover. Clamp :Insert the clamp to the hole of the fender fully. Check that all chassis bolts and nuts are tightened to their specified torque.