Operate the starter button 1-2 times for roughly 1 second to turn the engine over slowly, then insert the spark plug again;. The injection and ignition are timed on the four-stroke cycle by means of a tone wheel keyed on to the crankshaft 24-2 teeth and pick-up sensor. Engine Valve check standard clearance Inlet: 0. Maintenance Action Air filter - cleaning Air filter belt compartment - check Engine oil - change Valve clearance - check Electrical system and battery - check Coolant level - check Brake fluid level - check Engine oil - replacement. Maintenance -Adjust the distance if necessary by bending the side electrode very carefully. Pre-delivery Carry out the listed tests before delivering the vehicle.
Injection Check the resistance of the primary coil between pin 22 of the interface wiring and the green black cable of the injection load remote control base with the control unit disconnected and the remote con- trol disconnected. To reassemble, repeat the operation in the reverse order. Electrical system Front side 1. We have over 300,000 Vespa parts and Vespa accessories in stock and carry only the highest quality available. Start up the engine and wait for it to stop.
Chassis This section è is devoted to the operations that can be carried out on the vehicle's bodywork. An insufficient quantity of oil can cause serious damage to the engine itself. Front Removing the front wheel - Remove the 5 fixing screws indicated in the pho- tograph. The brake pad check spring 1. Access to taillight bulbs, stop light bulb and license plate bulb.
Specific tooling 020376Y Adaptor handle 020456Y Ø 24 mm adaptor 020363Y 20 mm guide Inspecting the driven fixed half-pulley - Measure the outer diameter of the pulley bushing. The tyres are equipped with wear indicators; the tyres should be replaced as soon as these indica- tors become visible on the tyre tread. The correct fluid level for front and rear brakes. Worn pads Contact an Authorised Piaggio Service Centre Air in the front and rear brake Contact an Authorised Piaggio circuits Service Centre. This is the result of the natural phenomenon of battery discharging plus residual absorption by vehicle components with constant power consumption. In all four-stroke engines, a loss of efficiency in oil performance and certain consumption should be considered normal.
Braking system This section è is devoted to the description of the brake system components. The further the piston falls inside the cylinder, the less the base gasket to be applied to recover the compression ratio and vice versa. The booklet also contains instructions for simple repairs. Lift the helmet compartment «B» and access the spark plug by reaching in with your hand. If the saddle gets stained, wipe the area and if necessary wash it with lukewarm water and neutral soap. Engine Oil pressure check - Remove the electrical minimum oil pressure switch connection and remove the switch. Haven't dared to exceed 60mph yet but it was certainly stable at that speed -- yet it makes me wonder whether I really should go faster.
It resets the trip odometer when pushed more than 3 seconds. Rules This section describes general safety rules for any maintenance operations performed on the scooter. The engine should be emptied by draining the oil from the drainage plug «B» of the gauze filter on the flywheel side. Engine Inspecting the valves - Measure the width of the sealing surface on the valve seats and on the valves. Vespa Gtv250 Gtv 250 Service Repair Workshop Manual Download can be very useful guide, and vespa gtv250 gtv 250 service repair workshop manual download play an important role in your products. Engine from vehicle This section describes the operations to be carried out when removing the engine from the vehicle. Suspensions - Before refitting the bracket in the wheel axle, place the O-ring as shown in the photograph so that it is correctly placed after fitting the bracket.
Instrument panel - Remove the rear handlebar cover;. To read the chassis number, lift the saddle and remove the helmet compartment «C». Transmission Automatic expandable pulley variator with torque server, V belt, automatic centrifugal dry clutch, gear reduction unit and transmission compartment with. To reassemble, repeat the operation but in reverse order. In the event of a malfunction to the system, the indicator led provides diagnostic in- formation to your Authorised Piaggio Service Centre through its blinking patterns. Removing the valves - Using the appropriate tool fitted with an adapter, remove the cotters, caps, springs and valves.
To reassemble, repeat the operation in the reverse order. Besides hours and minutes, month and day can also be displayed with the «T» button. The system is designed to provide the best performance acceleration and consumption while riding on both flat roads and uphill. The procedures to check the brake fluid level for the front and rear brakes are identical. Safety rules - If work can only be done on the vehicle with the engine running, make sure that the premises are well ventilated, using special extractors if necessary;. The procedures to checking the brake fluid level for the front and rear brakes are identical. For this reason it is advised that it be used only in exceptional circumstances.
Spa to be used by the workshops of Piaggio-Gilera dealers. It contains information, tips and precautions for using your vehicle. Engine scraper ring Standard opening: 0. With engine off and piston at the bottom dead centre, remove the spark plug, fill with 1÷2 cc oil larger amounts are dangerous for the engine itself. Immobiliser The electronic ignition system is controlled by the control unit with the integrated Immobilizer sys- tem.